Industrial Air Coolers
Adiabatic cooling unit for existing ventilation equipment
Adiabatic cooling unit for existing ventilation systems: humidifies and cools air at 2,000–30,000 m³/h without refrigerant gas, with up to 80% lower energy consumption.
Ecological operationThe device operates entirely ecologically and requires no refrigerant gas.
Adiabatic humidificationAdds moisture to the airflow and cools it within the range of 2,000 to 30,000 m³/h.
Energy SavingElectricity consumption is up to 80% lower compared to conventional air conditioning units.
High efficiencyUses high-efficiency cooling panels (type 5090).
Adiabatic air humidifier that adds moisture to the airflow and cools it within a range of 2,000 to 30,000 m³/h. The unit is suitable for use with air conditioning heat exchangers, ventilation units (AHU) or other systems
ADIABATIC COOL is an adiabatic air humidifier that adds moisture to the airflow and cools it within a range of 2,000 to 30,000 m³/h. The unit is suitable for use with air conditioning heat exchangers, ventilation units (AHU) or other systems where it is necessary to increase air humidity and cool the airflow. The air is cooled by directing outside air through a water-moistened panel, which makes the operation fully ecological and requires no refrigerant gas. Upon request, it is also possible to manufacture units with greater capacity or made entirely of stainless steel.
Main advantages
- Fully ecological operation – uses no refrigerant gas
- Electricity consumption up to 80% lower compared to conventional air conditioning units
- High-efficiency cooling panels (type 5090)
- Water tank made of AISI 316 stainless steel and corner posts made of AISI 304 stainless steel
- High-performance water pump with external rotor
- MET MANN's patented automatic drainage system
- Water distributor with adjustable flow rate
- Base frame with legs for easy transport and installation
- Hydraulic and electrical connections pre-connected at the factory
- Easy installation: only a single-phase electrical connection for the water pump and a water connection from the mains
- Low maintenance requirements: annual inspection of the cooling panels and general cleaning of the unit
Air flow2 000 kuni 30 000 m³/h
Cooling panel thickness100 mm or 200 mm
Water BoxAISI 316 stainless steel
Corner postsAISI 304 stainless steel
Electrical connectionSingle-phase (for the water pump)
Reduced energy consumptionConsumes up to 80% less electrical energy than conventional air conditioning systems.
Environmentally friendlyWork is fully ecological and requires no refrigerant gas.
Easy installationThe hydraulic and electrical connection is factory-assembled, requiring only a single-phase electrical connection and a water connection.
Low maintenance requirementsA yearly inspection of the cooling panels and general cleaning of the device is sufficient.
Easy transportThe leg-mounted base frame simplifies transport and installation.
Kliimaseadmete soojusvahetid
Ventilatsiooniseadmed (UTA)
Common questions about this product.
Frequently asked questions
What airflow range does the ADIABATIC COOL operate in, and is higher capacity available?
The unit operates within an airflow range of 2 000 to 30 000 m³/h. Upon request, higher-capacity units can also be manufactured.
With which systems is ADIABATIC COOL suitable for use?
The device is suitable for use in combination with air conditioning heat exchangers, ventilation units (AHU), or other systems where it is necessary to increase air humidity and cool the airflow.
Does the unit require refrigerant gas and how significant are the energy savings?
The device operates in a fully ecological manner and does not require refrigerant gas. Electricity consumption is up to 80% lower compared to conventional air conditioning units.
What is the maintenance requirement of the ADIABATIC COOL?
The equipment has low maintenance requirements: an annual inspection of the cooling panels and a general cleaning of the unit.
What are the device's connection requirements during installation?
Installation is straightforward: only a single-phase electrical connection for the water pump and a mains water connection are required. The hydraulic and electrical connections are pre-wired at the factory.
Need help finding the right solution?
We help you choose the solution that fits your needs and production.
Send request →Quality materialsDurable industrial quality and long service life.
Experienced partnerWe help design, install and maintain.
Support & spare partsFast help and spare-part availability throughout the lifecycle.
