Keevitusventilatsiooni projekteerimine ja väljaehitus
Birger OÜ uude tootmishoonesse ehitasime push-pull põhimõttel keevitusventilatsiooni, mis tagab kokku kuni 60 000 m³/h õhuringluse. Filtreerimiseks paigaldasime 2x GRAM ACF364DH topelttsükloni 45 kW ventilaatoritega ning filtreeritud õhk suunatakse tagasi halli. Kogu süsteemi juhib reaalajas üks juhtpaneel. Lahendus põhineb samal kontseptsioonil, mille rajasime varem Birgeri teise keevitushalli.
Projekti väljakutse
Birger OÜ rajas uue tootmishoone, kuhu oli vaja võimekat keevitusventilatsiooni, mis suudab suuremahulise tootmise saasteained usaldusväärselt eemaldada. Väljakutse oli tagada puhas õhk kogu hallis, ilma et väärtuslik soojus töökeskkonnast kaduma läheks. Loogiline valik oli tugineda kontseptsioonile, mis oli Birgeri teises keevitushallis juba edukalt tööle rakendatud.
Meie lahendus
Projekteerisime ja ehitasime välja push-pull põhimõttel toimiva keevitusventilatsiooni, mis on kohandatud tootmisruumi vajadustele ja keevituskohtade paigutusele.
- Push-pull süsteem, mis tagab kokku kuni 60 000 m³/h õhuringluse
- 2x GRAM ACF364DH topelttsüklon filtreerimiseks
- 45 kW ventilaatorid õhuvoolu tagamiseks
- Filtreeritud õhu tagassuunamine halli, nii et soojus jääb hoonesse
- Üks juhtpaneel, mis juhib kogu süsteemi reaalajas
Tulemus
Galerii
FAQ
Frequently asked questions
How much air circulation does this welding ventilation solution provide?
How is the filtered air and heat retention handled?
How is the system controlled?
What does the solution achieve in the production environment?
Do you offer both design and installation?
Projects
More similar projects
Welding hall ventilation solution with smart remote management
We built a push-pull general ventilation system for the welding hall with two separately controlled zones, ensuring a total air circulation of up to 60,000 m³/h (the requirement was ≥45,000 m³/h) and over 10,000 m³/h of fresh air. We installed two GRAM 364DH double cyclones with 45 kW fans and a C.I.C Jan Hrebec plate heat exchanger with water heating, which reduces heating demand. Compliance of air quality with health protection limit values was confirmed by measurements carried out together with the Health Board, and the entire system is controlled by a single control panel with real-time remote management.
Push-Pull welding ventilation for a metal production hall in Saue
At a metalworking company's production hall in Saue, we solved the blue welding fume problem using the Push-Pull method, as the use of welding arms was not possible due to the large components and continuous crane operation. We installed an FL series filter with GRAM welding cartridges, prepared a 3D piping installation drawing, and carried out the installation. The filtered air is directed into the hall from floor level, and the welding fumes are extracted from above the workstation, beneath the ceiling.
Factory Welding Workshop Push-Pull Ventilation
We upgraded the ventilation of the manual welding stations at Sami Tootmine's Valga factory in two areas, each with 10 workstations. We installed cyclone filters together with fans from the Danish manufacturer Gram Clean Air and designed a push-pull ventilation system with air calculations. We integrated automation that activates the filter system only when welding is actually taking place, ensuring energy savings and a clean working environment. In addition, we helped find a suitable welding filter for the robotic welding area.
